DeltaMyc Operation Manual J810018 (7 Oct 2014)
Introduction
7-3
Microscope mode ............................. 3-2, 3-17
Microscope Objective
window ..................3-3
microscope scan wizard ................. 3-22, 3-25
Microscope TCSPC Scan file ..................3-28
Microscope TCSPC-multi point mapping ...3-
28
monochromator .......................................... 6-1
Motor 1-3
connector.................................. 2-9
motorized
x,y
stage .... 0-1, 2-5, 2-9, 3-3–4, 3-
14–15, 6-1
MSDS.........................................................0-3
N
near-IR .......................................................0-1
neutral-density filters .................. 3-2, 4-4, 6-2
New
button ........................................ 3-1, 3-7
New Measurement
function ....... 3-20, 3-28
New Measurement
window .3-1, 3-6, 3-15, 3-
20
Next step
button .....................................3-23
NIM out
..................................................... 2-8
None
........................................................3-22
O
OK
button ..............3-11, 3-15, 3-17, 3-21–22
Open
function .........................................3-28
P
Parameter to be displayed
drop-down list
.............................................................3-32
Parameters
area .....................................3-27
PCI card ...................................................3-14
Photo and parameters
..........................3-26
Photo
item ...............................................3-25
Photos
folder ........3-15, 3-17–18, 3-22, 3-25
pinhole3-2–3, 3-8–9, 3-17, 3-21, 3-24, 4-4, 6-
1
Pixel Shape
............................................3-27
position 1................................................3-2–3
position 2................................................3-2–3
Power
inlet ................................................ 2-8
Power
socket ............................................. 2-8
power supply ..............................................3-1
PPD detector ............ 0-1, 2-6, 2-8, 4-4, 6-1–2
Print map
................................................ 3-27
Prompt
item ......................... 3-15, 3-18, 3-28
Properties
window .................................. 3-16
protective gloves........................................ 0-6
R
Ratemeters
window ................................ 3-18
Read this manual notice ............................ 0-6
Recommend
button ............................... 3-30
reference point ....................................... 3-4–5
reference position .................................... 3-11
Rel. Ampl.
............................................... 3-31
relative humidity........................................ 2-3
Resolution
area ...................................... 3-24
Run
button .............................................. 3-25
S
safety goggles ............................................ 0-6
safety summary.......................................... 0-5
safety training ............................................ 2-1
safety-training requirements ............... 2-1, 3-1
Save As
.................................................. 3-18
Save map
............................................... 3-27
Save picture to BMP file
button .. 3-17, 3-22
Scanning microscope
window .......... 3-23–24
Select Calibration Type
window ...... 3-4, 3-11
Select Point of Interest
................ 3-11, 3-16
Select point of interest
window ................ 4-4
Select position
window ............ 3-16–17, 3-21
Set Anchor
control ................................. 3-21
serial numbers............................................ 4-6
Service Department ................................... 4-6
softkey device ............................................ 2-9
software log files ....................................... 4-5
Stage calibration
.................... 3-3, 3-7, 3-10
Stage control
– Advanced
................... 3-14
Stage control
window ............................. 3-14
stage-controller ........................... 2-5, 3-5, 5-1
Start
button ........................ 3-15, 3-18, 4-4–5
Start
input ................................................. 2-8
Start
socket ............................................... 2-8
Stop
button................................... 3-25, 4-4–5
Stop
input.................................................. 2-8
Stop
socket................................................ 2-8
Store position
........................................ 3-17
