Honeywell VISTA-128BPT, Installation And Setup Manual, Page: 60 / 124

VISTA-128BPT/VISTA-250BPT Installation and Setup Guide
5-4
FIELD TITLE and DATA ENTRIES EXPLANATION
∗ ∗ ∗ ∗
34
Secondary Phone Number
Enter 0-9; #11 for
∗
, #12 for #, #13 for a 2-
second pause.
Enter the secondary phone number, up to 17 digits. The secondary phone
number
is used if communication on the primary number is unsuccessful, or if
split/dual reporting is desired. Do not fill unused spaces.
NOTE: If this field is programmed, a secondary subscriber account number
(field *90) must also be programmed.
∗ ∗ ∗ ∗
35
Download Phone Number
Enter 0-9; #11 for
∗
, #12 for #, #13 for a 2-
second pause.
Enter the downloading phone number, up to 17 digits. Do not fill unused
spaces.
NOTE: This field is applicable only if downloading is utilized.
∗ ∗ ∗ ∗
36
Download ID Number
Make entries as 2-digit numbers as follows:
00=0 01=1 02=2 03=3 04=4 05=5
06=6 07=7 08=8 09=9 10=A 11=B
12=C 13=D 14=E 15=F
Enter eight digits.
NOTE: This field is applicable only if downloading is utilized.
∗ ∗ ∗ ∗
37
Download Command Enables
0 = disable
1 = enable
Enabling a function means that you are able to perform that function via the
ADEMCO Compass Downloading software.
Functions are as follows: Dialer Shutdown; System Shutdown; Not Used;
Remote Bypass; Remote Disarm; Remote Arm; Upload Program; Download
Program.
For UL installations, all entries must be
0 .
∗
∗ ∗
∗
38
Prevent Zone XXX Bypass
(partition-specific)
Enter a zone number (001-250) .
Enter 000 if all zones can be bypassed.
Enter three digits for zone that cannot be bypassed by the user.
NOTES:
The actions manual bypass, group bypass, auto-stay, and STAY/INSTANT
arming modes cannot bypass any zone programmed in this field.
The system will not arm if the zone is programmed with the vent zone or force
arm fault attributes.
ULC
Force Arming is not a ULC Listed feature and
must be disabled for ULC installations.
∗
∗ ∗
∗
39
Enable Open/Close Report for
Installer Code (partition-specific)
0 = disable
1 = enable
If enabled, whenever the Installer Code is used to arm or disarm the partition,
an open/close report is sent to the central station.
∗
∗ ∗
∗
40
Enable Open/Close report for
Keyswitch
0 = disable
1 = enable
If enabled, whenever the keyswitch is used to arm or disarm the partition, an
open/close report is sent to the central station.
∗
∗ ∗
∗
41
Normally Closed or EOLR (Zones
2-8)
0 = EOLR used
1 = normally closed
If 0, end-of-line resistors must be used on zones 2-8.
If 1 end-of-line resistors cannot be used and only normally closed devices
must be used.
Must be
0 for UL installations.
∗
∗ ∗
∗
42
Dial Tone Pause
Enter the wait time for dial tone detection:
0 = 5 seconds; 1 = 11 seconds; 2 = 30
seconds.
Enter the time the system waits for dial tone before dialing.
Must be 0 for UL installations.
∗ ∗ ∗ ∗
44
Ring Detection Count
Enter 00 to disable ring detection.
Enter 01-14 for ring counts of 1-14.
Enter 15 to select Answering Machine Defeat
Mode
Only applicable if station-initiated downloading will be used.
NOTES:
In the Answering Machine Mode, the caller should let the phone ring once,
then hang up, and call again within 30 seconds. The system, upon hearing
one ring followed by nothing, does not answer the first call, but readies itself to
pick up on the first ring of the next incoming call that is received within 30
seconds (i.e., the downloader calling again).
Must be
00 for UL installations.