manualshive.com logo in svg

Honeywell ESSER IQ8Control M, Installation Instruction, Page: 78 / 138

Share
Download
Honeywell ESSER IQ8Control M Installation Instruction Download Page 78

Fire Alarm Control Panel IQ8Control C / M 

 

78

  

FB 798951.10.GB0 / 04.15

 

7.1.10  FOC transmission line in the essernet

®

  

Alternatively, the essernet

® 

can be set up with fibre optic cables. Optional fibre-optic converters are required for 

this. 
This FOC converter (Part No. 784763 / 784764 / 784765) converts electrical signals into optical signals for reliable 
data transmission under difficult transmission conditions in which, for example, copper cables cannot be used. It 
is possible to use both FOC and conventional copper cable within one network simultaneously. The connection 
of fire alarm system control panels through FOC requires at least one FOC converter and one essernet

®

 module 

per FACP. Depending on the type of fibre optics used, FOCs can be used to connect two fire alarm control panels 
spaced a max. of 3,000 metres apart. The FOC converter can optionally be supplied with the FOC connection 
type F-ST (Part No. 784763) or F-SMA (Part No. 784764).  
The FOC converter must be fitted directly inside the control panel housing or the same control cabinet as the 
housing. When doing so, the FOC converter must be fitted directly to the DIN rail (Part No. FX808387) without 
using any additional fastening material. 

essernet

®

FOC

FOC

FOC

FOC

Fibre Optics Link

Fibre Optics Link

 

Fig. 66: Schematic wiring of an fibre optics cable  

 

 

Please refer to the manual (Part No. 798636 / 798963.10) for detailed information about fibre optic 
wirings. 

 
 

Requirements / restrictions 

 

Each loop segment needs to be equipped with two multimode optical fibres. 

 

The fibres must be connected directly and without interruption 
(e.g. they cannot be connected using multiplexers). 

 

Fibre type G50 / 125 µm, with a max. attenuation of 6 dB, corresponds to a max. length of approx. 2000 m and 
fibre type G62,5 / 125 µm, with a max. attenuation of 9 dB, corresponds to a max. length of approx. 3000 m. 

 

Maximum of 16 FOC lines per essernet

®

 when using a transmission speed of 62,5 kBd.  

 

Maximum of 31 FOC lines per essernet

®

 when using a transmission speed of 500 kBd.  

 

7.1.11 Specification 

Main voltage 

: 

24 V DC 

Quiescent current 

: 

37 mA 

Weight : 

100 

g 

Dimension (w x h x d) 

: 

27 x 93 x 113 mm 

Summary of Contents for ESSER IQ8Control M











































































































































Reviews:

No comments