manualshive.com logo in svg

Honeywell ESSER IQ8Control M, Installation Instruction, Page: 63 / 138

Share
Download
Honeywell ESSER IQ8Control M Installation Instruction Download Page 63

Fire Alarm Control Panel IQ8Control C / M 

 

FB 798951.10.GB0 / 04.15

 

63

 

6.4.4 Technical data Field device module 

 

Operating voltage 

:  Internal via the power supply module, +5 V DC / + 12V DC 

Quiescent current 

:  approx. 15 mA @ 12 V DC 

Fuse F1 
Fuse F2, F3, F4 

: 
: 

T1A – slow blow (relay K1) 
T2A - slow blow (relays K2 to K4) 

Relay K1 

: 

Relay for connecting a master box. May also be used as a freely 
programmable relay. 
Selection of operating mode and emergency function by means of 
jumpers. 

Contact rating when used as a >non-monitored change-over 
contact< contact rating < 30 V DC/ max.1 A.  
No dry contact cause of the integrated EMI protection. 

Relay K2, K3, K4 

: 

Relay with common function. May also be used as a freely 
programmable relay. 
Selection of operating mode and emergency function by means of 
jumpers. 

Contact rating when used as a >non-monitored change-over 
contact<, contact rating < 30 V DC/ max.2A 
No dry contact cause of the integrated EMI protection. 

Fire department operating panel 

:  8 digital inputs  

8 outputs - max. 12 V DC / 20 mA per output 

 

Internal primary loop  

:  monitored 10 k

 (normal) / 5 k

 (FIRE) / 1 k

 (fault) 

Application e.g. for essernet

®

-emergency operation 

 

 

Compatibility : 

Part 

No.772479 

 Field device module without micro module slot 

Part No.772477 

 Field device module with micro module slot 

 

 

 

The IQ8Control FACP's relays may only be connected to DC voltages. No AC voltage may be 
applied, not even when a relay is programmed as a >non-monitored change-over contact<! 

 

 

Summary of Contents for ESSER IQ8Control M











































































































































Reviews:

No comments