manualshive.com logo in svg

Honeywell ESSER IQ8Control M, Installation Instruction, Page: 119 / 138

Share
Download
Honeywell ESSER IQ8Control M Installation Instruction Download Page 119

Fire Alarm Control Panel IQ8Control C / M 

 

FB 798951.10.GB0 / 04.15

 

119

 

Trouble 

Code No. 

Possible Cause 

1st. measure 

2nd. measure 

069 

There are more detectors on the 
loop than programmed in the 
customer data. 

If this change is not desired, 
connect service PC and run 
a wiring recognition. Re-
program customer data. 

If this change is not desired, 
connect service PC and run a 
wiring recognition. Re-program 
customer data. 

070 

Error during detector data 
allocation. 

Perform detector data 
assignment again. 

--- 

080 

This detector change may only 
be performed with the service PC 
because this detector required 
customer data that cannot be 
generated in the FACP itself. 

If this change is not desired, 
connect service PC and run 
a wiring recognition. Re-
program customer data. 

--- 

081 

The detector has been replaced 
with an OTI-detector. The sensor 
type has changed in comparison 
with the customer data. 

Check whether detector type 
change is desired; if it is, 
activate loop. 

Otherwise install detector you 
require and re-start >Detector 
change< 

082 

The detector has been replaced 
with an OT-detector. The sensor 
type has changed in comparison 
with the customer data. 

Check whether detector type 
change is desired; if it is, 
activate loop. 

Otherwise install detector you 
require and re-start >Detector 
change< 

083 

The detector has been replaced 
with an I-detector. The sensor 
type has changed in comparison 
with the customer data 

Check whether detector type 
change is desired; if it is, 
activate loop 

Otherwise install detector you 
require and re-start >Detector 
change< 

084 

The detector has been replaced 
with a TM-detector. The detector 
type has changed in comparison 
with the customer data. 

Check whether detector type 
change is desired; if it is, 
activate loop. 

Otherwise install detector you 
require and re-start >Detector 
change< 

085 

The detector has been replaced 
with a TME-detector. The 
detector type has changed in 
comparison with the customer 
data. 

Check whether detector type 
change is desired; if it is, 
activate loop. 

Otherwise install detector you 
require and re-start >Detector 
change< 

086 

The detector has been replaced 
with a TD-detector. The detector 
type has changed in comparison 
with the customer data. 

Check whether detector type 
change is desired; if it is, 
activate loop. 

Otherwise install detector you 
require and re-start >Detector 
change< 

087 

The detector has been replaced 
with an O-detector. The detector 
type has changed in comparison 
with the customer data. 

Check whether detector type 
change is desired; if it is, 
activate loop. 

Otherwise install detector you 
require and re-start >Detector 
change< 

088 

Detector circuitry has been 
changed at detector location. 
Now detector has neither external 
circuit (relay / LED) nor isolating 
relay. 

If this change is desired, 
connect service PC and run 
a wiring recognition. 
Re-program customer data. 

--- 

 

 

Summary of Contents for ESSER IQ8Control M











































































































































Reviews:

No comments