manualshive.com logo in svg

Honeywell ESSER IQ8Control M, Installation Instruction, Page: 68 / 138

Share
Download
Honeywell ESSER IQ8Control M Installation Instruction Download Page 68

Fire Alarm Control Panel IQ8Control C / M 

 

68

  

FB 798951.10.GB0 / 04.15

 

7.1.1 esserbus

® 

loop module (Part No. 784382 / 784382.10 / 784382.D0) 

The loop module allows for esserbus

® 

 

connection and is configured with Programming software tools 8000  

from V1.15.  

esserbus

®

Fire alarm and extinguishing 

computer 8010

 

Fig. 57: Exampleesserbus

® 

 

K2 (B)

K1 (A)

LED 2

LED 3

LED 4

LED 1

Loop module

X1

 

Fig. 58: Loop module (Part No. 784382 / 784382.10 / 784382.D0) 

 
 

 

 

Connect cable shielding of the loop only at one side. 

 

When using the module in door control systems, place the enclosed labels on or in the FACP 
housing (see chapter 14.1). 

 
 

X 1 

64-way plug connector to micro module slot of the Basic module, Field device module or 
Extension module 

K1, K2 

Bi-directional loop interrogation by loop isolators 
(K1 = A+, A- / K2 = B+, B-) 

LED 1 

(SMD) red, flashing  

   in normal mode in time with communication on the loop 

(SMD) red, lit 

  Short circuit on loop 

LED 2 

(SMD) yellow, lit 

 Module 

faulty 

LED 3 

(SMD) red, flashing 

  + 24 V power supply failure or communication to 

 

 

control panel processor interrupted 

(SMD) red, lit 

  Module in CPU failure mode 

 

 

(control panel CPU failure) 

LED 4 

(SMD) yellow, flashing 

  Processor program running – normal mode  

(SMD) yellow, flashing rapidly  

  Module in test mode  

Summary of Contents for ESSER IQ8Control M











































































































































Reviews:

No comments