manualshive.com logo in svg

Honeywell ESSER IQ8Control M, Installation Instruction, Page: 128 / 138

Share
Download
Honeywell ESSER IQ8Control M Installation Instruction Download Page 128

Fire Alarm Control Panel IQ8Control C / M 

 

128

  

FB 798951.10.GB0 / 04.15

 

17  Top hat rail mounting kit (Part No. 788652) 

In the FACP IQ8Control C / M can be installed a top hat rail mounting kit (optional). This mounting kit comprises 
of a mounting base, a standard 35 mm top hat rail (C-profile mounting), M5 x 30 bolts, M5 x 50 screws and insert 
nuts. In order to facilitate mounting and removal, the top hat rail is fitted to the mounting base by means of two 
screws.   
 

Variant 1 

With the kit a maximum of two optional module housings (Part No.788603 or 788603.10) can be installed inside 
the panel housing. The module housing for top hat rail mounting accepts all the format 72 x 65 mm or 82 x 72 mm 
(W x H) FACP boards e.g. esserbus

®

 transponder, Kit redundant transmission path. 

Variant 2 

In addition to the module housing, an optical fibre converter (Part No.784763 / 64) with a clip for top hat rail 
mounting may be installed inside the panel housing. 

 

 

Mounting 

Mounting example – Variant 1:  
Top hat rail mounting kit with module housings (optional) 
Components of the Top hat rail mounting kit 
 

4

3

2

1

 

Fig. 107: Components of the Top hat rail mounting kit 

 
 
 

 

Mounting base for Top hat rail 

 

Fastening screws for Top hat rail 

 

2 x Module housing Part No.788603 / 788603.10 (optional) 

 

Standard Top hat rail, 35 mm 

 
 

 

See product group catalogue 'fire alarm technology' and documentation on the mounting rail 
installation kit for further information. 

 

 

 

Summary of Contents for ESSER IQ8Control M











































































































































Reviews:

No comments