manualshive.com logo in svg

Honeywell AlarmNet GSMBR, Installation And Setup Manual, Page: 8 / 64

Share
Download
Honeywell AlarmNet GSMBR Installation And Setup Manual Download Page 8

GSMBR / iGSMBR Installation and Setup Guide 
 

1-4

 

Specifications 

Mechanical 

Dimensions:

 8.4" x 8.0" x 1.5" 

Weight:

 2.4 lbs., with battery 

Environmental 

Operating temperature:

 –20º to +55ºC 

Storage temperature:

 –40º to +70ºC 

Humidity:

 0 to 95% relative humidity, non-condensing 

Altitude:

 10,000 ft. operating, 40,000 ft. storage 

Electrical 

Input Power:

 16.5VAC, 40VA transformer (Honeywell

 

Model No. 1361), or 12 

VDC from the control panel, or when a LYNXR-I Series control panel is used 
the ECP power output provides power. 

Backup Battery:

 6V, 3.1AH, Honeywell part number K14139 (included). 

Expected Battery Life:

 5 Years (approx.) 

Current Drain:

 65mA average standby, 500mA peak transmit 

Fault Relay Output:

 Open collector, 12VDC, 20mA 

Input Trigger Levels:

 

(V+) 2V – 14V,  or (V–) 0V – 1V 

Ethernet 
(iGSMBR only) 

Network Standard:

 IEEE 802.3u compliant 

Data Rate:

 10Base-T / 100Base-T with auto detect 

Ethernet Cable:

 Cat. 5 (min), MDI/MDI-X auto crossover 

Transceiver Type 

GSM/GPRS 

 
 

 

 

 
 

Summary of Contents for AlarmNet GSMBR

































































Reviews:

No comments