manualshive.com logo in svg

Honeywell AlarmNet GSMBR, Installation And Setup Manual, Page: 48 / 64

Share
Download
Honeywell AlarmNet GSMBR Installation And Setup Manual Download Page 48

GSMBR / iGSMBR Installation and Setup Guide 
 

6-2

 

 

RDR1 RDR2 RDR3 
OK      OK     OK 

 

A summary of the tests is displayed after Redir 3 is tested.  The 
example shows that the tests of all three connection points, or 

Redirs, were successful.  If an error occurred at any point, the 

summary will display "FAIL" under the faulty Redir. 

Possible Errors Running Network Diagnostics 

Errors may occur either while tracing the connection to a given Redir or while testing the 

service at a given Redir.  The following list highlights the most common errors.  Please 
contact the AlarmNet Technical Assistance Center (TAC) for help regarding any errors NOT 

listed below: 

Possible Errors 

 

 

Testing Redir 

x 

FAIL before Gtwy

 

While tracing the connection to Redir x, the trace fails before ever 
reaching the local gateway (router). 

 

 

Testing Redir 

x 

FAIL at Gtwy

 

While tracing the connection to Redir x, the trace fails after reaching 

the local gateway (router). 

 

 

Testing Redir 

x 

FAIL at Pvt IP

 

While tracing the connection to Redir x, the trace fails after reaching 
the private IP. 

 

 

Testing Redir 

x 

FAIL on IP Addr

 

While tracing the connection to Redir x, the trace fails after reaching 
the public IP. 

 

 

Redir 

x

 

ERR:Proxy 18

 

After a successful trace to Redir x, the test of the network service 
timed out without a response. 

 

 
 
 
 
 
 
 
 
 
 
 
 

 

Summary of Contents for AlarmNet GSMBR

































































Reviews:

No comments