manualshive.com logo in svg

Honeywell AlarmNet GSMBR, Installation And Setup Manual, Page: 16 / 64

Share
Download
Honeywell AlarmNet GSMBR Installation And Setup Manual Download Page 16

GSMBR / iGSMBR Installation and Setup Guide 
 

2-8

 

Backup Battery Connection 

The included battery is used for backup in the event of a system power loss.  

If using the 

LYNXR-I, the communications module's backup battery is not used.

  Instead, backup 

power is supplied by the LYNXR-I. 

NOTE:

 The backup battery should be replaced every 3 years or when a low battery report is 

received at the Central Station. 

•

 

The battery can provide over 24 hours of system life in the event of a power failure.  

•

 

A power loss message (programmable option) can alert the AlarmNet Control Center 

when power is lost.  Power loss messages are reported within 1-3 hours of actual loss.  

•

 

The communications module sends a low-battery message (programmable option) when 

the battery drops to 5.7V ±5%. 

•

 

The system shuts down when the battery voltage falls below 5.1V, therefore radio 

transmissions are no longer possible.  

•

 

If system power is restored before the module shuts down, a power-on restore message is 

sent within 1-3 hours after power is restored, and the battery is recharged using the 

communications module's internal battery charger.   

•

 

If system power is restored after the communications module has shut down, the module 
initializes itself and the battery will recharge. 

Install the battery as follows, and refer to the 

Summary of Connections

 diagram at the end of 

this document. 
1.

 

Place the battery inside the case back.  

2.

 

Snap the right side of the battery clip onto the inside of the case back and secure the left 
side with the screw provided.   

NOTE:

 DO NOT connect the battery at this time. 

 

Initial Power-Up Sequence  

NOTE:

 Initially, all communications module programming options are set to the factory 

default settings. 
Before connecting power, check that the following have been completed: 
1.

 

If using ECP, 4204 or 2-4204 Mode, terminal block TB1 V+ and GND terminals are 

connected to the control panel’s auxiliary power output: 12VDC nominal. 

2.

 

Plug in the transformer (or other main power source).  

3.

 

Connect the red and black battery cables to the battery terminals.  Connect the battery 
cable to connector J1. 

4.

 

Power up the control panel. 

 
 
 
 
 

Summary of Contents for AlarmNet GSMBR

































































Reviews:

No comments