Honeywell AlarmNet GSMBR Installation And Setup Manual Download Page 40

Page: 40 / 64

GSMBR / iGSMBR Installation and Setup Guide

4-2

Register using the Programming Tool

The interactive registration feature allows the installer to register the module through a

series of keyboard commands on the 7720P Programming Tool. This method of registration
lets the installer monitor the registration process.

Registering …

Once the installation is complete, press the [Shift] and the up arrow
[

] key. The registration message is sent and the unit waits for the

acknowledgment.

Registration
SUCCESS

If this is a new installation and the city, central station, and

customer numbers have been correctly entered, the module is
registered and this message is displayed.

The communications module is now in full service and
available for alarm reporting to the central station.

Possible Errors

Registration BAD
Timed Out

Displayed if no response to the registration request is received.

Registration BAD
Pri Sub ID BAD

Indicates the city, central station, or customer number for the labeled

account(s) is not accepted. The ID information was either entered
incorrectly, or the central station failed to pre-authorize programmed

ID numbers with AlarmNet customer service.

Registration BAD
2

Sub ID BAD

Indicates the city, central station, or customer number for the

Secondary account is not accepted. The ID information was either
entered incorrectly, or the central station failed to pre-authorize

programmed ID numbers with AlarmNet customer service.

Registration BAD
Pri&Sec – IDs BAD

Displayed when both primary and secondary subscriber IDs are

invalid.

Registration BAD
Pri ID – Need PIN

Displayed if this is a repair/replacement, or an error was made in

programming the Primary account information for an existing
account. This prompt appears for 2 seconds. See the

Replacing an

existing module

section below for further displays.

Registration BAD
2

ID – Need PIN

This prompt is displayed if this is a repair/replacement, or an error

was made in programming the Secondary account information for an
existing account. This prompt appears for 2 seconds. See the

Replacing an existing module

section below for further displays.

Registration BAD
Pri&2

– Need PIN

This prompt is displayed if this is a repair/replacement, or an error

was made in programming BOTH the Primary and Secondary
account information for an existing account. This prompt appears for

2 seconds. See the

Replacing an existing module

section below for

further displays.

Summary of Contents for AlarmNet GSMBR

































































Search results

Summary of Contents for AlarmNet GSMBR

Reviews:

Honeywell AlarmNet GSMBR, Installation And Setup Manual, Page: 40 / 64

Search results

Summary of Contents for AlarmNet GSMBR

Reviews: