Honeywell AlarmNet GSMBR, Installation And Setup Manual, Page: 55 / 64

D-1
Appendix D: LED Display Reference
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
TB 1
6 7 8 5
10 11
9 2 3 4 1
PRIMARY POWER: 9 - 16.5 VAC CURRENT: 900mA PEAK, 70mA STANDBY BATTERY: 8V. 3.1 AHr FOR 24 Hr BACKUP
FCC:XXXXXXXXXX IC: YYYYYYYYYY
RSSI
M0
M1
GPRS
IBS
RED
BLA
CK
iGSMBR-016-V0
RSSI / MODE
AND
STATUS LEDs
1
ON – Message tr
ansmission pending.
Q
UICK PERIODIC BLINK – Nor
mal.
F
AST BLINK – Message w
aiting f
or netw
or
k A
CK.
SLO
W BLINK – Idle po
w
er abnor
mal.
SLO
W BLINK – In unison with g
reen LED
, registr
atr
ation in prog
ress
.
Ethernet Link/Activity GREEN
ON – Ether
net Link detected.
OFF – No link detected. F
AST BLINK –
T
ransmitting/Receiving Data.
ON – 100 MB/S link to Inter
net.
OFF – 10 MB/S link to Inter
net.
BLINKING – Netw
or
k collision detected.
OFF – Nor
mal.
Link Speed GREEN
Netw
ork Collision
YELLO
W
Note:
If all LEDs F
AST BLINK in unison with the RSSI LEDs this
indicates a Hardw
are Error
.
ON – No contact with netw
or
k.
OFF – Nor
mal.
SLO
W BLINK – Loss of comm
unication with the panel (ECP f
ault).
F
AST BLINK – No netw
or
k contact AND loss of comm
unication with the panel.
ON – NO
T registered with Alar
mNet.
OFF – Registered with Alar
mNet.
F
AST BLINK – Do
wnload session with Compass in prog
ress
.
SLO
W BLINK – In unison with y
ello
w LED
, registr
ation in prog
ress
.
MODE SWITCH
+
-
TAMPER
SWITCH
Note:
F
or iGSMBR only
.
GRN
YEL RED
ECP OFF OFF Zone ON OFF 4204 OFF ON 2 - 4204 ON ON
MODULE'S RECEIVED SIGNAL STRENGTH (RSSI)
When the
Mode Switch
is NOT depressed, LED 1 will illuminate red.
The remaining LEDs indicate RSSI (Received Signal Strength).
MODULE'S OPERATION MODE
When the
Mode Switch
IS depressed, LED 1 will be OFF.
LEDs 2 and 3 indicate the module's communication mode with the control panel.
Mode LED 2 (yellow) LED 3 (yellow
)
MODULE'S STATUS When the
Mode Switch
IS depressed, LED 1 will be OFF.
LEDs 4, 5, and 6 indicate the module's Status.
FAST BLINK - Module registered, second site available, excellent signal strength.
LED 4 (green) LED 5 (green) LED 6 (green)
ON - Connected to Internet.
ON - Module registered, no second site available.
ON - GPRS service available. OFF - No GPRS service available
OFF - Module not registered with network carrier.
FAST BLINK - GPRS in use.
SLOW BLINK - Module registered, second site available, and low signal strength.
NORMAL BLINK - Module registered, second site available, acceptable signal strength.
OFF - Not connected to Internet.