Honeywell AlarmNet GSMBR Installation And Setup Manual Download Page 10 | Manualshive

Page: 10 / 64

Honeywell AlarmNet GSMBR Installation And Setup Manual Download Page 10

GSMBR / iGSMBR Installation and Setup Guide

2-2

Mounting the Module

Mounting Procedure

1.

Locate the case back over selected mounting position such that the opening in the case
back is aligned with the wire/cable opening on the mounting surface.

2.

Pass the wires/cable through the opening in the case back, or route through the
removable knockouts located on the back cover.

3.

Secure the case back to the mounting surface using four screws (supplied).

4.

When all wiring is completed, attach the case front. Position the top first, then press the

bottom section until it snaps in place. Secure bottom using cover screw (supplied).

iGSMBR_quick-guide-01-V0

MOUNTING

SCREW (4)

MOUNTING

SURFACE

COVER

SCREW

WIRING
KNOCKOUT

WIRING

KNOCKOUTS

FOR

EXTERNAL

ANTENNA

50 OHM,

MMCX

ONLY

7720P

PROGRAMMER

PORT

NOT

FOR

TELEPHONE

SERVICE

USE!

PRIMARY

POWER

: 9 -

16.5

VAC

BATTERY:

6V.3.

1 AHr

FOR

24 Hr

BACKUP

FCC

ID: GIPMC56

IC: Y267W

- MC56

GSM

GPPS

WEB

MODE 2

MODE 1

RSSI

Honeywell

RX

TX

MAC

LABEL

HERE

TRANSMIT

LED

Figure 2-1. Standard Mounting

Wiring the Module

NOTE:

A minimum of 22 AWG wire (unshielded) is recommended for power and data wires.

For long power runs, 18 AWG may be specified.

Wiring for ECP, 4204 and Two-4204 Modes

Most Honeywell ADEMCO control panels support LRR-ECP data communication, (such as

the VISTA-10P, VISTA-15P, VISTA-20P, VISTA-128BP, VISTA-128FBP and LYNXR-I).
However, there are some panels that do not. Check the Installation and Setup Guide for the

control panel to see if it supports ECP communication.

Connect the communications module to the control panel's ECP terminals, in parallel with
keypads and other ECP peripheral devices. The wire length/gauge requirements are the

same for all ECP devices. To wire the module for ECP or 4204 modes, see

Figure 2-2

.

«
...
8
9
10
11
12
...
»

Summary of Contents for AlarmNet GSMBR

































































Reviews:

No comments