manualshive.com logo in svg

Honeywell AlarmNet 7847i-E, Installation And Setup Manual

Share
Download
Honeywell AlarmNet 7847i-E Installation And Setup Manual Download Page 49

Appendices 

A-3

 

 

Network Connectivity Display 

The Network Connectivity display can only be viewed with the cover removed.  It is used as a 
visual indication of 7847i/7847i-E

 

network activity.  

7847i-E-032-V0

NETWORK CONNECTIVITY

LED DISPLAY

NETWORK COLLISION (YEL)

LINK SPEED (GRN)

ETHERNET LINK/ACTIVITY (GRN)

 

 

Figure 15.  7847i/7847i-E Network Connectivity Display 

The Network Connectivity Display consists of three LEDs. They function as follows: 

LED COLOR 

LED LABEL 

DESCRIPTION

 

YELLOW NETWORK 

COLLISION 

BLINKING – Network collision detected. 

OFF – Normal. 

1

ST

 GREEN 

LINK SPEED 

ON – 100 MB/S link to Internet. 

OFF – 10 MB/S link to Internet. 

2

ND

 GREEN 

ETHERNET 
LINK / 
ACTIVITY 

ON – Ethernet link detected. 

OFF – No Ethernet link detected. 

FAST BLINK – Transmitting/Receiving data. 

 

NOTE: 

When "Enable Pwr Save" is enabled, LED status is displayed once every 15 seconds.

 

 

Summary of Contents for AlarmNet 7847i-E

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands