manualshive.com logo in svg

Honeywell AlarmNet 7847i-E, Installation And Setup Manual

Share
Download
Honeywell AlarmNet 7847i-E Installation And Setup Manual Download Page 4

7847i/7847i-E Installation and Setup Guide 

ii 

Alternative Modes (Zone Trigger, 4204 and Two-4204) .......................................................................................... 3-9

 

Zone Trigger Mode ..................................................................................................................................... 3-9

 

4204 Emulation Mode ................................................................................................................................. 3-9

 

4204 Emulation Mode Options ................................................................................................................... 3-9

 

Alternative Mode Programming .............................................................................................................................. 3-10

 

Exiting Programming Mode .................................................................................................................................... 3-20

 

Setting Factory Defaults .................................................................................................................................... 3-20

 

SECTION 4: Registration .......................................................................................................................... 4-1

 

Registering the 7847i/7847i-E ................................................................................................................................... 4-1

 

Registering through AlarmNet Direct Website (does not apply if using Private LAN) .............................. 4-1

 

Using the Tamper Switch ............................................................................................................................ 4-2

 

Using the Programming Tool ...................................................................................................................... 4-2

 

Register by Phone........................................................................................................................................ 4-4

 

SECTION 5: Programmer Keyboard Commands ................................................................................ 5-1

 

Programmer Keyboard Commands ........................................................................................................................... 5-1

 

System Status Displays ............................................................................................................................... 5-2

 

SECTION 6: Network Diagnostics .......................................................................................................... 6-1

 

Running Network Diagnostics on the 7847i/7847i-E using AlarmNet ..................................................................... 6-1

 

Possible Errors Running Network Diagnostics ........................................................................................... 6-2

 

Running Network Diagnostics on the 7847i-E

 

using a Private LAN ........................................................................ 6-3

 

Possible Errors Running Network Diagnostics using a Private LAN.......................................................... 6-4

 

Appendices ...................................................................................................................................................A-1

 

Appendix A : Summary of LED Operation .............................................................................................................. A-1

 

Status Display Operation............................................................................................................................ A-1

 

Network Connectivity Display ................................................................................................................... A-3

 

Mode and Status LED Display ................................................................................................................... A-4

 

Mode and Status Indicator Switch.............................................................................................................. A-4

 

Appendix B : Central Station Messages ....................................................................................................................B-1

 

Appendix C : IP Downloading ..................................................................................................................................C-1

 

General Information ....................................................................................................................................C-1

 

Direct Wire Setup........................................................................................................................................C-1

 

Appendix D : Glossary ............................................................................................................................................. D-1

 

Summary of Connections Diagram…………………………………………………………..……….Inside Back Cover

Summary of Contents for AlarmNet 7847i-E

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands