manualshive.com logo in svg

Honeywell AlarmNet 7847i-E, Installation And Setup Manual

Share
Download
Honeywell AlarmNet 7847i-E Installation And Setup Manual Download Page 3

i 

Table of Contents 

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

 

SECTION 1: General Information........................................................................................................... 1-1

 

Introduction ............................................................................................................................................................... 1-1

 

System Features......................................................................................................................................................... 1-1

 

About Private Network Application .......................................................................................................................... 1-1

 

About AlarmNet-i Internet Application..................................................................................................................... 1-2

 

Encryption ................................................................................................................................................................. 1-2

 

Enterprise Encryption Related Functions .................................................................................................................. 1-2

 

Installation Key (for Private LAN) ............................................................................................................................ 1-2

 

Recovery Mode ......................................................................................................................................................... 1-2

 

Remote Services ........................................................................................................................................................ 1-3

 

Modes of Operation ................................................................................................................................................... 1-3

 

ECP Mode ................................................................................................................................................... 1-3

 

Zone Trigger Mode ..................................................................................................................................... 1-3

 

4204 Mode and Two-4204 Mode ................................................................................................................ 1-3

 

Module Supervision Features .................................................................................................................................... 1-4

 

Specifications ............................................................................................................................................................ 1-4

 

Mechanical .................................................................................................................................................. 1-4

 

Electrical ..................................................................................................................................................... 1-4

 

Ethernet ....................................................................................................................................................... 1-4

 

Environmental ............................................................................................................................................. 1-4

 

SECTION 2: Mounting and Wiring ......................................................................................................... 2-1

 

Mounting the 7847i/7847i-E...................................................................................................................................... 2-1

 

Wiring the 7847i/7847i-E .......................................................................................................................................... 2-2

 

Wiring for ECP, 4204 and Two-4204 Modes.............................................................................................. 2-2

 

Wiring for Zone Trigger Mode.................................................................................................................... 2-3

 

Power Connections and Options................................................................................................................................ 2-4

 

Ethernet Connections................................................................................................................................................. 2-4

 

Initial Power-Up Sequence.......................................................................................................................... 2-5

 

SECTION 3: Programming the 7847i/7847i-E ....................................................................................... 3-1

 

General Information .................................................................................................................................................. 3-1

 

Using the AlarmNet Direct Website............................................................................................................ 3-1

 

Using a 7720P Programming Tool .............................................................................................................. 3-1

 

Using the Control Panel Programming Mode ............................................................................................. 3-2

 

Programming Conventions.......................................................................................................................... 3-2

 

ECP Mode Programming........................................................................................................................................... 3-2

 

ECP Status Codes ................................................................................................................................................ 3-9

 

Summary of Contents for AlarmNet 7847i-E

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands