Honeywell AlarmNet 7847i-E Installation And Setup Manual Download Page 40

Page: 40 / 64

7847i/7847i-E Installation and Setup Guide

5-2

DHCP
OK/BAD

DHCP (Dynamic Host Configuration Protocol) indicates
server is performing satisfactorily.
Press the [space] key to go to the Physical Link display.

[F]

Testing Gateway

Run Network Diagnostic Test

Performs a set of network diagnostics that tests the
integrity of the links between the unit and the various
connection points (Redirs) to AlarmNet. Refer to
Section 6:

Network Diagnostics

System Status Displays

[S]

ECP 67 Tm Flt
xx 5 OK

ECP Mode

Displays the zone and system fault status.
Press the [space] key to go to the next field.
Press the [backspace] key to go to the previous field.

1234 67 Tm Flt
5555 xx 5 OK

4204 Emulation Mode

Displays the zone and system fault status.
Press the [space] key to go to the next field.
Press the [backspace] key to go to the previous field.

12345678 Tm Flt
5555555x 5 OK

Two-4204 Emulation Mode

Displays the zone and system fault status.
Press the [space] key to go to the next field.
Press the [backspace] key to go to the previous field.

1234567 Tm Flt
5555555 5 OK

Zone Trigger Mode

The status of the unit can be viewed on the 7720P. The
status display includes:

•

Zone input status

(1234567)

- the

numbers 1-7 represent the 7 mappings of
the zone input, and follow Honeywell's
ADEMCO high-speed format codes:

= New Event

= Normal

= Not Enabled

•

– Tamper status follows high-speed format

codes above.

•

Flt

– Represents radio faults:

= Normal ; No fault

– No network connectivity over IP and

fault time has expired

– No network connectivity over IP and

fault time has NOT yet expired.

NOTE:

The 7720P will not operate if the power line

voltage is removed.

[T]

Test Msg Sent

Test Alarm

Sends a test alarm to AlarmNet only if Private LAN is
not enabled; otherwise, it is sent the Primary CS IP and
the Secondary if it is enabled.

Summary of Contents for AlarmNet 7847i-E

































































Search results

Summary of Contents for AlarmNet 7847i-E

Reviews:

Brands by name

Popular brands

Honeywell AlarmNet 7847i-E, Installation And Setup Manual

Search results

Summary of Contents for AlarmNet 7847i-E

Reviews:

Brands by name

Popular brands