Honeywell 4800dr - Document Camera Barcode Manual Download

Page: 11 / 146

1 - 3

4. Plug the power supply into the cable.

5. Once the document reader has been fully connected, power up the computer.

6. Program the document reader for a TTL-232 Serial Port interface using the Plug and Play barcode

page 1-5

Supported Terminals

Programming the Interface - Plug and Play

Plug and Play barcodes provide instant document reader set up for commonly used interfaces.

USB Connection

IBM SurePos

Scan one of the following “Plug and Play” codes to program the document reader for IBM SurePos (USB
Hand Held document reader) or IBM SurePos (USB Tabletop document reader).

Note:

After scanning one of these codes, you must power cycle the cash register.

Each barcode above also programs the following suffixes for each symbology:

Terminal

Terminal ID

TTL-232

000

USB COM Port Emulation

130 (default)

USB PC Keyboard

124

USB Mac Keyboard

125

USB POS

131

Symbology

Suffix

EAN-8

EAN-13

UPC-A

UPC-E

Code 39

00 0A 0B

Interleaved 2 of 5

00 0D 0B

Code 128

00 18 0B

IBM SurePos

(USB Hand Held Document

Reader) Interface

IBM SurePos

(USB Tabletop Document

Reader) Interface

Summary of Contents for 4800dr - Document Camera



















































































































































Search results

Summary of Contents for 4800dr - Document Camera

Reviews:

Related manuals for 4800dr - Document Camera

Brands by name

Popular brands

Honeywell 4800dr - Document Camera, Barcode Manual

Search results

Summary of Contents for 4800dr - Document Camera

Reviews:

Related manuals for 4800dr - Document Camera

Brands by name

Popular brands