Honeywell 4800dr - Document Camera Barcode Manual Download

Page: 10 / 146

1 - 2

1. Connect the appropriate interface cable to the document reader first, then to the computer.

2. Program the document reader for a USB interface using the Plug and Play barcodes beginning on

page 1-3

3. The document reader beeps.

4. Verify the document reader operation by scanning a barcode from the

Sample Symbols

in the back

of this manual.

For additional USB programming and technical information, refer to Honeywell “USB Application Note,”
available at

www.honeywell.com/aidc.

Connecting the Document Reader with TTL-232 Serial Port

Note:

See

"Document Reader Models"

on page 1-1 to determine which interfaces apply to your

document reader.

1. Turn off power to the terminal/computer.

2. Connect the appropriate interface cable to the document reader.

Note:

For the document reader to work properly, you must have the correct cable for your type of
terminal/computer.

3. Plug the serial connector into the serial port on your computer. Tighten the two screws to secure the

connector to the port.

Summary of Contents for 4800dr - Document Camera



















































































































































Search results

Summary of Contents for 4800dr - Document Camera

Reviews:

Related manuals for 4800dr - Document Camera

Brands by name

Popular brands

Honeywell 4800dr - Document Camera, Barcode Manual

Search results

Summary of Contents for 4800dr - Document Camera

Reviews:

Related manuals for 4800dr - Document Camera

Brands by name

Popular brands