manualshive.com logo in svg

Honeywell 4800dr - Document Camera, Barcode Manual

Share
Download
Honeywell 4800dr - Document Camera Barcode Manual Download Page 56

6 - 8

Code 93

< Default All Code 93 Settings >

Code 93

Code 93 Message Length

Scan the barcodes below to change the message length.  Refer to 

Message Length Description

 (page 6-

2) for additional information.  Minimum and Maximum lengths = 0-80.  Minimum Default = 0, Maximum 
Default = 80.

Code 93 Code Page

Code pages define the mapping of character codes to characters.  If the data received does not display 
with the proper characters, it may be because the barcode being scanned was created using a  code 
page that is different from the one the host program is expecting.  If this is the case, scan the barcode 
below, select the code page with which the barcodes were created (see 

Code Page Mapping of Printed 

Barcodes

 on page A-4), and scan the value and the 

Save

 barcode from the 

Programming Chart

 on the 

inside the back cover of this manual.  The data characters should then appear properly.

*  On

Off

Minimum Message Length

Maximum Message Length

Code 93 Code Page

Summary of Contents for 4800dr - Document Camera



















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands