1
www.observint.com
ALI-TP3002L_CQ
190801
Installation
Before installation:
•
Make sure that the device is in good condition and all the assembly parts are included.
•
Check the specification of the products for the installation environment.
•
Make sure that the wall or the ceiling is strong enough to withstand 4 times the weight of the
camera.
•
To avoid fire or shock hazard, use only UL listed power supplies. Verify that the power supply will
provide the rated voltage and wattage for the camera. See the
Specifications
section.
During installation:
•
Camera Lens
: Handle the camera carefully to prevent scratching or soiling the lens. If the lens or IR
array shield becomes soiled, clean it only with approved products. See the
Cleaning
section.
•
Power supply
:
Camera drop cable
: The camera drop cable includes two connectors:
—
Video coax with BNC connector
: For transmission of the video signal across a coax (75 Ω)
extension cable to a compatible recorder.
—
Power connector:
The camera can be powered by 12 Vdc. When applying 12 Vdc power,
observe the power polarity shown on the connector. See the picture to the left for the connector
polarity configuration.
•
Ground
: A ground cable can be used to ground a junction box. A terminal for an earth ground is
provided inside the box. Always ground the box if it is installed in a moist or humid environment.
Follow local electrical codes for proper grounding.
Step 1. Route interface cables to the camera
Video and power interface cables connect directly to the camera drop cable (see photo above).
The ALI-A6 junction box is compatible with the camera. If using a junction box, connectors between the
camera drop cable and extension cables can be stored within the box,and an earth ground cable can be
used to ground the box and camera.
NOTE
When selecting a mounting location for the camera
• Make sure that there are no reflective surfaces near to the camera lens. White light from the camera
may bounce back onto the lens causing reflections.
• Determine how wiring is routed into the camera. The cable can be routed through an access hole in the
mounting plate, or through the cable in the mounting base.
The camera includes connectors for the following:
•
Video coax
(required): The video drop cable can connect to a video coax extension cable from a
Video Recorder or compatible monitor.
•
12 Vdc power input
: Refer to the Specifications section of this document for voltage and current
requirements. ALWAYS COMPLY WITH THE POLARITY SHOWN IN THE PICTURE ABOVE.
1.
Route a video coax extension cable from a compatible video recorder (DVR) to where the camera
will be installed.
2.
Route 12 Vdc power extension cables from an adequate power source to the location where the
camera will be installed.
3.
If using a junction box, you can attach an earth ground extension cable to the junction box. Route
the cable to the location of the junction box, if needed. Always follow local electrical codes when
using an earth ground.
CAUTION
Do not apply power to the camera at this time. Before applying power to the camera, ensure that
the polarity is correct. An incorrect connection may cause a malfunction and can damage the
camera.
Step 2. Install the camera
The camera can be mounted onto a the ALI-AJ6 junction box, or directly onto a wall or ceiling. The surface
should support at least four times the weight of the camera and junction box (if used). The video/power
drop cable from the camera can be routed either through mounting surface or through a cable channel in
the mounting base.
Installing the camera with a junction box
NOTE
: The ALI-AJ1 and ALI-AJ6 junction boxes are very similar.
The ALI-AJ6 junction box is shown below. It can be attached to a wall or ceiling. Video and power
extension cables can be routed in through the opening in the back of the box or through the conduit
coupling, and attached to the camera drop cables inside the box.
ALI-TP3002L 2 MP 4-in-1
Bullet Camera
with IllumiNite Technology
Quick Installation Guide
The ALIBI ALI-TP3002L indoor / outdoor bullet camera includes a 4 -in-1 switchable video output (TVI/
AHD/CVI/CVBS) with with an 2 MP sensor and IllumiNIte technology for color vision at night. This camera
features:
•
2 Megapixel (1920
1080 pixels) high-performance CMOS sensor up to 30 fps
•
Switchable video output for TVI, AHD, CVI, or CVBS (4 in 1)
•
3.6 mm fixed lens offers horizontal FOV of 83.6°
•
Starlight 2.0 chipset
•
Color: 0.0005 Lux, 0 Lux with white light
•
Up to 65 ft white light distance
•
True WDR up to 130 dB
•
IP67 weather-rated with -40°F – 140°F operating temperatures
•
OSD menu (up-the-coax OSD control)
•
Compatible with ALI-AJ1 junction box, ALI-AJ6 junction box
Camera
body
Adjustable
Mounting
bracket
Mounting
base
Lens
White light LED
ALI-TP3002L camera
Switch
button
Switch button usage
Cap for switch cable
12 Vdc power in
HD video BNC connector
Camera drop cable connectors
What’s in the box
Box contains:
•
Installation Guide
•
Drill template
•
Mounting screws and wall inserts
What you need
To install the camera, you will need:
•
12 Vdc power source. See
Specifications
for requirements.
•
Tools and additional fasteners (may be required) for mounting the camera
•
Video, power and ground (if needed) extension cables
