Honda DS-2CC102P(N)-IRT Owner'S Manual Download Page 63

Page: 63 / 115

SERVICING YOUR GENERATOR

5. Inspect the spark plug. Replace

it if the electrode is worn or
fouled, or if the insulator is
cracked or chipped.

6. Measure the spark plug

electrode gap with a wire-type
feeler gauge. Correct the gap, if
necessary, by carefully bending
the side electrode.

The gap should be:
0.028–0.031 in (0.7–0.8 mm)

7. Make sure that the spark plug

sealing washer is in good condition, and thread the spark plug in by
hand to prevent cross-threading.

8. After the spark plug is seated, tighten with a spark plug wrench to

compress the washer.

If reinstalling a used spark plug, tighten 1/8–1/4 turn after the spark
plug seats.
If installing a new spark plug, tighten 1/2 turn after the spark plug
seats.

TORQUE:

13.3 lbf·ft (18 N·m, 1.8 kgf·m)

A loose spark plug can overheat and damage the engine.
Overtightening the spark plug can damage the threads in the cylinder
head.

9. Attach the spark plug cap.

10. Reinstall the spark plug inspection cover and tighten the cover

screw.

11. Close the left maintenance cover.

SEALING WASHER

0.028–0.031 in
(0.7–0.8 mm)

SIDE ELECTRODE

INSULATOR

31Z37613.book 61 ページ２０１５年１２月２日　水曜日　午前１０時４５分

Summary of Contents for DS-2CC102P(N)-IRT




















































































































Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands

Honda DS-2CC102P(N)-IRT, Owner'S Manual

Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands