Honda DS-2CC102P(N)-IRT Owner'S Manual Download Page 33

Page: 33 / 115

OPERATION

• Use the recoil starter when

the battery voltage is too low
to turn the starter motor.

a. Turn the MAIN switch to

the ON position.

b. Open the right maintenance

cover by turning its latch
counterclockwise.

c. Pull the starter grip lightly

until you feel resistance;
then pull briskly in the
direction of the arrow as
shown.

• Do not exceed 20

degrees from horizontal
when pulling the starter
grip.

• Do not allow the starter

grip to snap back against
the engine. Return it
gently to prevent
damage to the starter.

• Do not let the starter

rope rub against the
generator body, or the
rope will wear out
prematurely.

d. Close the right

maintenance cover by
turning its latch clockwise.

6. If you wish to use the

Eco-Throttle system, turn the
Eco-Throttle switch to the ON
position after the engine has
warmed up for 2 or 3 minutes.

MAIN SWITCH

20°

STARTER GRIP

ECO-THROTTLE SWITCH

OFF

31Z37613.book 31 ページ２０１５年１２月２日　水曜日　午前１０時４５分

Summary of Contents for DS-2CC102P(N)-IRT




















































































































Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands

Honda DS-2CC102P(N)-IRT, Owner'S Manual

Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands