Honda DS-2CC102P(N)-IRT Owner'S Manual Download Page 20

Page: 20 / 115

CONTROL & FEATURES

Maintenance Covers

Open and close the maintenance cover for maintenance of the
EU7000is.
Open the right maintenance cover, to use the recoil starter when the
battery is discharged. Be sure the maintenance cover is closed while
the generator is running.

Running the generator with maintenance cover(s) open will adversely
affect the engine performance, and will cause the generator to overheat.

Open the right maintenance cover for:

• Engine oil inspection/replacement
• Recoil starter

Open the left maintenance cover for:

• Spark plug inspection/replacement
• Air cleaner inspection/cleaning

To open:

Turn the latch 90° counterclockwise to unlock and open the
maintenance cover.

To close:

Turn the latch 90° clockwise to lock while pushing the cover.

LATCH

LEFT MAINTENANCE COVER

LATCH

RIGHT MAINTENANCE COVER

Push the cover closed and turn
the latch.

31Z37613.book 18 ページ２０１５年１２月２日　水曜日　午前１０時４５分

Summary of Contents for DS-2CC102P(N)-IRT




















































































































Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands

Honda DS-2CC102P(N)-IRT, Owner'S Manual

Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands