Honda DS-2CC102P(N)-IRT Owner'S Manual Download Page 77

Page: 77 / 115

TAKING CARE OF UNEXPECTED PROBLEMS

ENGINE LACKS POWER

NO POWER AT THE AC RECEPTACLES

Possible Cause

Correction

Air filter restricted.

Clean or replace air filter (see
pages 58, 59).

Bad fuel, generator stored
without treating or draining
gasoline, or refueled with bad
gasoline.

Drain fuel tank (see page 70).
Refuel with fresh gasoline (see
page 53).

Fuel filter restricted, fuel system
malfunction, fuel pump failure,
ignition malfunction, valves
stuck, etc.

Take the generator to an
authorized Honda servicing dealer,
or refer to the shop manual.

Possible Cause

Correction

OUTPUT indicator is OFF, and
OVERLOAD ALARM indicator is
ON.

Check AC load. Stop and restart
the engine.
Check the cooling air inlet. Stop
and restart the engine.

AC Circuit protector(s) tripped.

Check AC load and reset AC
circuit protector(s) (see page 15).

GFCI system activated.

• GFCI receptacle

(120 V 20 A duplex receptacle):
Test GFCI and press the RESET
button (see page 35).

• Replace or repair power tool or

appliance.

Faulty power tool or appliance.

Replace or repair power tool or
appliance.
Stop and restart the engine.

Faulty generator.

Take the generator to an
authorized Honda servicing dealer,
or refer to the shop manual.

31Z37613.book 75 ページ２０１５年１２月３日　木曜日　午前９時３３分

Summary of Contents for DS-2CC102P(N)-IRT




















































































































Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands

Honda DS-2CC102P(N)-IRT, Owner'S Manual

Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands