Honda DS-2CC102P(N)-IRT Owner'S Manual Download Page 35

Page: 35 / 115

OPERATION

STARTING THE ENGINE with REMOTE CONTROL (Optional part)

1. Determine the voltage requirements and adjust the voltage selector

switch, as needed.

2. Turn the MAIN switch of the generator to the ON position.

3. Turn the MAIN switch of the remote control to the ON position.

4. Press and release the ENGINE START button.

The ENGINE START button functions for 5 seconds. As soon as the
engine starts, the starter will stop automatically.
The pilot lamp comes on when the engine starts.

If the engine fails to start, wait at least 10 seconds before operating
the starter again.

MAIN SWITCH

OFF

PILOT LAMP

ENGINE START BUTTON

MAIN SWITCH

OFF

31Z37613.book 33 ページ２０１５年１２月２日　水曜日　午前１０時４５分

Summary of Contents for DS-2CC102P(N)-IRT




















































































































Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands

Honda DS-2CC102P(N)-IRT, Owner'S Manual

Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands