Honda DS-2CC102P(N)-IRT Owner'S Manual Download Page 106

Page: 106 / 115

104

OPTIONAL PARTS

4. Pass the remote control cable through the supplied wire grommet,

and fit the grommet into the battery maintenance cover knockout.

5. Plug the remote control cable into the connector.
6. Install the battery maintenance cover and tighten the cover screw.

7. To avoid accidentally unplugging the remote control cable, secure the

cable to the generator frame with a cable tie as shown.

• Never operate the generator

without the battery maintenance
cover in place, as poor engine and
generator performance will result.

• Install the plug to the connector

when the remote control kit is
removed.

GROMMET

REMOTE CONTROL
CABLE

BATTERY MAINTENANCE COVER

REMOTE CONTROL BOX

REMOTE CONTROL CABLE

CABLE TIE

PLUG

31Z37613.book 104 ページ２０１５年１２月２日　水曜日　午前１０時４５分

Summary of Contents for DS-2CC102P(N)-IRT




















































































































Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands

Honda DS-2CC102P(N)-IRT, Owner'S Manual

Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands