Honda DS-2CC102P(N)-IRT Owner'S Manual Download Page 100

Page: 100 / 115

ASSEMBLY

Battery

WARNING:

Battery posts, terminals, and related accessories contain

lead and lead compounds.

Wash hands after handling.

The battery is disconnected and strapped into the battery tray for
shipment.

1. Remove the battery maintenance cover (see page 64).
2. Remove the battery strap from the bottom hook, and then remove

the battery.

3. Only remove the battery cables from the twist clip.

Make sure that the 4-pin blue coupler harness is secured with the
twist clip.
Charge the battery properly. See page 66.
Reinstall the battery.

4. Remove the protective cover from the battery positive (+) terminal,

and connect the positive (+) cable to the battery positive (+)
terminal. Make sure to cover the terminal with the battery boot.

5. Connect the negative (–) cable to the battery negative (–) terminal.
6. Secure the battery by hooking the strap onto the bottom hook of the

generator.

7. Install the battery maintenance cover in the reverse order of removal

(see page 64).
Never operate the generator without the battery maintenance cover
in place, as poor engine and generator performance will result.

TWIST CLIP

BOTTOM
HOOK

4-PIN BLUE COUPLER HARNESS

BATTERY CABLES

NEGATIVE (–) CABLE

BATTERY STRAP

BATTERY

POSITIVE (+) CABLE

BATTERY BOOT

31Z37613.book 98 ページ２０１５年１２月２日　水曜日　午前１０時４５分

Summary of Contents for DS-2CC102P(N)-IRT




















































































































Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands

Honda DS-2CC102P(N)-IRT, Owner'S Manual

Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands