Hisun HS5DUTV-2 Maintenance Handbook Download Page 68 | Manualshive

Page: 68 / 355

background image

MAINTENANCE AND ADJUSTMENT OF THE EV

68

11. Check if there is any abnormal noise during the driving.
12. Check if the maximum speed of the EV does not exceed 40km/h. EV is not allowed to

be driven at a speed higher than 40km/h.

MAINTENCE AND ADJUSTMENT OF THE EV

To ensure trouble-free vehicle performance, it is very important to follow an

established preventive maintenance program. Meanwhile, regular maintenance can
greatly extend the service life of EV.

Regular and consistent vehicle maintenance can prevent vehicle downtime and

expensive repairing cost that could be resulted because of neglect. This will also
prevent further damage to the vehicle and avoid the possibility of injury.

If you are not eligible or technologically limited for regulated maintenance, please

contact your local distributor/dealer to perform all repairs or semiannual or annual
periodic service.

NOTE

⚫

If any problems are found during scheduled inspection or service, do not
operate the vehicle until repairs are made. Failure to make necessary
repairs could result in ﬁre, property damage, severe personal injury, or
death.

⚫

Only trained technicians could serve or repair the vehicle and its battery
charger. The appropriate instructions must be used when performing
maintenance, service, or accessory installation.

⚫

Hot! Do not attempt to serve a hot motor.

⚫

To avoid unintentionally starting the vehicle during the process of
repairing, please disconnect the battery.

⚫

After disconnecting the batteries, wait 90 seconds for the controller
capacitors to discharge. The maintenance can be done only after this step.

⚫

To maintain the EVs or battery chargers, you must wear certified safety
glasses to protect eyes. When working nearby the battery, you must wear
face shield and rubber gloves.

⚫

When maintaining close to the electrical system or upon the electrical
system, use the insulated tools. To be more careful to avoid parts or
electrical short circuit.

⚫

Both the Periodic Service Schedule and Periodic Lubrication Schedule
must be followed to keep vehicle in optimum operating condition.

⚫

If  the  vehicle  is  constantly  subjected  to  heavy  use  or  used  under  severe
operating  conditions,  the  frequency  of  the  preventive  maintenance
procedure  should  increase,  compared  with  that  recommended  in  the
periodic service and lubrication schedules.

«
...
66
67
68
69
70
...
»

Summary of Contents for HS5DUTV-2




































































































































































































































































































































































Reviews:

No comments

Related manuals for HS5DUTV-2

HealthyWhite 700 series

Brand: Magnavox Pages: 16

Brand: DAY Useful Everyday Pages: 12

Brand: Kambrook Pages: 6

Combi-Steam MSLQ 600

Brand: V-ZUG Pages: 2

Brand: Sunbeam Pages: 32

Maxell IZR-N1261

Brand: IZUMI Pages: 92

Brand: evowera Pages: 11

Brand: Hyundai Pages: 9

Brand: Philips Pages: 3

Brand: Philips Pages: 4

Brand: Philips Pages: 3

Brand: Philips Pages: 3

Brand: Philips Pages: 2

CoolSkin HS8440

Brand: Philips Pages: 2

Coolskin HS8060

Brand: Philips Pages: 2

Brand: Philips Pages: 36

Brand: Philips Pages: 136

Brand: Philips Pages: 138

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands