Hisun HS5DUTV-2 Maintenance Handbook Download

Page: 161 / 355

CHASSIS

- 161-

Brake performance degressive

1. Check whether disc plates abrasion exceeded limits.

2. Check whether brake shoe of clamp abrasion

exceeded limits or

polluted by friction material such

as oil.

、

Check whether the oil cup of brake fluid lack oil.

Grinding noises emerged from
front brake or brake plate
become red during drive due
to superheat.

1. Check whether brake plate deformed.

2. Check whether hydraulic cylinder of brake clamp

locked or brake clamp assembly parts deformed.

Grinding noises emerged from
rear brake or brake plate
become

red during drive

1. Check whether brake plate deformed.

2. Check whether hydraulic cylinder of brake clamp

locked or brake clamp assembly parts deformed.

3. Check whether rear brake clamp parking institution

running flexible or return accurately.

Off tracking by braking at high-
speed

1. Check whether front brake power deviation from left

and right is within specified scope.

2. Check whether front brake power degressive caused

to rear wheel locked before front wheel in brake
process.

3. Check whether left and right absorber spring force

deviation is exceeded specified value.

Off tracking by braking at
high-speed

4. Check whether front wheel and front wheel axle nut
loosen or damaged.

5. Check whether front wheel hub inner spline and front
wheel axle outer spline worn or loosen.

6. Check whether rubber cushion connected to front
suspension rocker and frame damaged.

Other system malfunction inspection

No.

Phenomenon

Measure

Steering wheel loosen, shift
up and down

Check whether steering wheel clip loosen or

damaged.

2. Check whether steering column clip and clip seat

loosen or damaged.

Summary of Contents for HS5DUTV-2




































































































































































































































































































































































Search results

Summary of Contents for HS5DUTV-2

Reviews:

Related manuals for HS5DUTV-2

Brands by name

Popular brands

Hisun HS5DUTV-2, Maintenance Handbook

Search results

Summary of Contents for HS5DUTV-2

Reviews:

Related manuals for HS5DUTV-2

Brands by name

Popular brands