Hisun HS5DUTV-2 Maintenance Handbook Download Page 240

Page: 240 / 355

CHASSIS

- 240-

SPECIFICATION OF WHEEL AND TYRE

Wheel
hub
Dimension

Tyre

Dimension

Tyre

Pressure

(Kpa
/psi)

Front
Whee
l

12×6(min) 25×8-12(min)

138/20

14×7(max

)

26×9-14(max)

Rear
Whee
l

12×8(min) 25×10-12(min)

138/20

14×9(max

)

26×11-
14(max)

• Since wheels and tyres are crucial to the vehicle

operation, inspection for tyre pressure and profile

depth is necessary.

• To ensure maximum security and longer life

expectancy of the wheel, please periodically

inspect the tyre pressure and profile depth.

Insufficient tyre pressure can result in not only

intensified wearing of the tyre but also instability

during the course of operating the vehicle (such

as hard turning). Excessive tyre pressure can

also reduce the friction force between the tyre

and ground, causing spinning or lose of control.

Therefore, please ensure the tyre pressure strictly

complies with figures shown in the chart above.

• Before operating the vehicle each time, please

check if profile depth of the tyre is over worn,

which might result in spinning, instability, lose of

control and other potential security risk of the

vehicle.

Summary of Contents for HS5DUTV-2




































































































































































































































































































































































Search results

Summary of Contents for HS5DUTV-2

Reviews:

Related manuals for HS5DUTV-2

Brands by name

Popular brands

Hisun HS5DUTV-2, Maintenance Handbook

Search results

Summary of Contents for HS5DUTV-2

Reviews:

Related manuals for HS5DUTV-2

Brands by name

Popular brands