Hilti DS TS 5-SE Operating Instructions Manual Download Page 33 | Manualshive

Page: 33 / 40

Hilti DS TS 5-SE Operating Instructions Manual Download Page 33

33

Maintenance

1. Accessories / tool set

A set of tools and other accessories is supplied with every DS TS 5-SE electric wall saw. These items help to ensure
that the electric wall saw can be operated efficiently and safely. The individual items (wearing parts) can be reordered
from your Hilti representative. The item numbers of the accessories and wearing parts are listed in the instruc-
tions supplied with the accessories / tool set.

Ordering designation

Qty.

Use

Accessory / tool

Complete set

Open-end / ring wrench, 19 mm

1

Tightening all nuts, screws and locking devices

Hex. wrench with T-grip

1

Carriage, flush cutting, roller play adjustment

ABP blow out pump

1

Blowing out anchor holes and, in winter, blowing
water out of the saw head.

2-metre folding rule

1

Measuring position of fastenings

Wooden pencil, long

2

Marking position of fastenings

Spirit level

1

Used by the operator

UTP cleaning cloth

1

Cleaning

Hilti spray

1

Cleaning / lubrication

Flat brush

1

Cleaning

Ear protectors

1

To be worn by operator for personal protection

Protective goggles

1

To be worn by operator for personal protection

Hex. screw, M12

×

40

10

Fastening the rail support

Hex screw, M12

×

70

10

Fastening the rail support

Washer

10

Fastening the rail support

Nut with collar, M12

20

Fastening the rail support

Rail clamp assembly

1

Fastening the rail support

DS-ESS 1 end stop

3

End stop on the rail, stops saw at end of rail

Steel wedge

4

Securing the concrete block

Rubber fastener for guard

2

Fastening blade guard on saw head

Plastic plug, M10

10

Blade flange, covering flush holes

Plastic plug, M12

2

Closes the central M12 threaded hole
during flush cutting

Special countersunk head screw, M10 6

Flush cutting, fastening saw blade

Special hex. screw, M12

×

25

1

Fastening saw blade flange / blade

O-ring for hex. screw, M12

1

For blade flange

Instructions for accessories / tools

1

Accessories, tools and wearing parts

Operating instructions

1

DS TS5-SE electric wall saw

Audio-visual instructional aids

CD-ROM

The following items are supplied fitted to the saw head

Water connection coupling

2

Water connection at the saw head

Plastic plug

3

Blade flange / cover for flush holes

CEE 16 A connector (3

×

400 V) /

1

Fit to user's extension cable, if necessary

CEE 32 A connector (3

×

200 V)

Please refer to the instructions for accessories / tools for information on other wearing parts.

«
...
31
32
33
34
35
...
»

Summary of Contents for DS TS 5-SE









































Reviews:

No comments