Hilti DS TS 5-SE Operating Instructions Manual Download Page 14 | Manualshive

Page: 14 / 40

Hilti DS TS 5-SE Operating Instructions Manual Download Page 14

14

DS-RC-TS 5-E remote control unit

No.

Designation

쐃

Remote control unit housing

쐇

Grips / control panel protection bars

쐋

Display with operating controls

쐏

Shoulder belt with fastener

��

Attachment point for belt fastener

��

Rear side of remote control unit: Instructions /
sawing guidelines

6.1

6. Parts of the electric wall saw

Technical data and description

쐇
쐋

쐃

쐏

쐄

쐂

Electric power and water connections

No.

Designation

Function

쐋

Power cable from mains supply

The power cable is permanently attached to the
electric wall saw (no plug connection at the wall saw).
Cable length: 7 m

Caution:

Connect the electric wall saw only to the

specified mains voltage. Please refer to the rating
plate.

쐏

Remote control connection

Socket for the remote control cable

쐄

Cooling water supply connection

Cooling water supply connection with standard
Gardena coupling. The water serves to cool the electric
motors, the control electronics and the saw blade.

쐂

Cooling water return connection

When the saw is operated with a minimum of cooling
water at the saw blade, the water regulation valve

쐇

can be adjusted to redirect water to the return

circuit

쐂

5.4

5

2

6

6

5

1

4

3

Positioned towards water connections = the cooling water
is directed into the return circuit but a minimum quantity
of approx. 0.5 l / min. always flows to the saw blade.

«
...
12
13
14
15
16
...
»

Summary of Contents for DS TS 5-SE









































Reviews:

No comments