Hilti DS TS 5-SE Operating Instructions Manual Download Page 19 | Manualshive

Page: 19 / 40

Hilti DS TS 5-SE Operating Instructions Manual Download Page 19

19

The DS-RFIX SI rail support

쐃

Baseplate

��

Slot for M12 anchor screw

��

Levelling screws

��

Rail clamping piece

쐄

Knurled-head screw

쐂

M12 fastening nut with collar

2.4

Operation

The DS-RFSI rail support

No.

Designation

��

Baseplate

��

Slot for M12 anchor screw

쐋

Ball swivel for rail angle adjustment (max. 45°)

��

Clamping screw for angle adjustment

��

90° locking position: locked when the
half-moon is turned towards the ball

��

Released position: released when the
half-moon is turned away from the ball

��

Rail clamping piece

��

Knurled-head screw

��

M12 fastening nut with collar

쐅

Fastening fork (360° pivot)

2.3

3

10

5

4

9

7

8

2

1

6

360

×

Mounting the D-R 100/230 SI rail on the rail

support

쐃

Slide the clamping piece into the rail profile. The
knurled-head screw (a) can be tightened to prevent
movement or loss of the clamping piece.

��

Slide the clamping piece onto the fastening fork of
the rail support.

��

Use the 19 mm AF open-end wrench to firmly tight-
en the M 12 nut with collar (b) of the clamping piece.

��

Releasing the rail: Use the open-end wrench to release
the M12 nut with collar (b) of the clamping piece and
slide the clamping piece out of the fastening fork on
the rail support.

2.5

3

4

1

2

a

b

쐏

쐄

쐂

쐃

쐇

쐋

«
...
17
18
19
20
21
...
»

Summary of Contents for DS TS 5-SE









































Reviews:

No comments