HIKVISION HiWatch HWI-B120H-U User Manual Download Page 60

Page: 60 / 193

Network Camera User Manual

Log Searching

To export the log files, click

Export

to save the log files.

System Service

Purpose:

System service settings refer to the hardware service the camera supports. Supported

functions vary according to the different cameras. For the cameras support IR Light,

ABF (Auto Back Focus), Auto Defog, or Status LED, you can select to enable or

disable the corresponding service according to the actual demands.

ABF:

When ABF function is enabled, you can click

on PTZ control panel to

realize auxiliary focus.

Third Stream

: For some models, third stream is not enabled by default. Check

Enable Third Stream

to enable the function.

eMMC Protection

If you enable eMMC protection, the lifespan of the eMMC is

displayed.

Enable Motion Detection: Check

Enable Motion Detection

to enable the function.

Summary of Contents for HiWatch HWI-B120H-U


































































































































































































Search results

Summary of Contents for HiWatch HWI-B120H-U

Reviews:

Related manuals for HiWatch HWI-B120H-U

Brands by name

Popular brands

HIKVISION HiWatch HWI-B120H-U, User Manual

Search results

Summary of Contents for HiWatch HWI-B120H-U

Reviews:

Related manuals for HiWatch HWI-B120H-U

Brands by name

Popular brands