HIKVISION HiWatch HWI-B120H-U User Manual Download

Page: 96 / 193

Network Camera User Manual

performance. The camera adjusts video-related parameters automatically, and the

pre-set video-related configuration is invalid. A reboot is required for the function to

take effect.

Note:

Bandwidth adaptation is only available for certain camera models.

Network Service

You can control the ON/OFF status of certain protocol that the camera supports.

Note:

•

Keep unused function OFF for security concern.

•

Supported function varies according to camera models.

WebSocket

and

WebSockets

WebSocket or WebSockets protocol should be enabled if you use Google Chrome

45 and its above version or Mozilla Firefox 52 and its above version to visit your

camera. Otherwise, live view, image capture, and digital zoom function cannot be

used.

If the camera uses HTTP, enable

WebSocket

If the camera uses HTTPS, enable

WebSockets

SDK Service

and

Enhanced SDK Service

If you want to add the device to the client software, you should enable SDK Service

or Enhanced SDK Service.

SDK Service:

SDK protocol is used.

Enhanced SDK Service:

SDK over TLS protocol is used. Communication

between the device and the client software is secured by using TLS (Transport

Layer Security) protocol.

TLS (Transport Layer Security)

The device offers TLS 1.1 and TLS 1.2. Enable one or more protocol versions

according to your need.

Summary of Contents for HiWatch HWI-B120H-U


































































































































































































Search results

Summary of Contents for HiWatch HWI-B120H-U

Reviews:

Related manuals for HiWatch HWI-B120H-U

Brands by name

Popular brands

HIKVISION HiWatch HWI-B120H-U, User Manual

Search results

Summary of Contents for HiWatch HWI-B120H-U

Reviews:

Related manuals for HiWatch HWI-B120H-U

Brands by name

Popular brands