HIKVISION HiWatch HWI-B120H-U User Manual Download

Page: 144 / 193

Network Camera User Manual

143

Region Exiting Detection

Check

Enable

checkbox to enable the function.

Select the

Region

from the drop-down list for detection settings.

Set the Max. Size and Min. Size for valid targets. Targets smaller or larger than

the valid target size are not able to trigger detection.

Max. Size

: The maximum size of a valid target. Targets with larger sizes would

not trigger detection.

Min. Size

: The minimum size of a valid target. Targets with smaller sizes would

not trigger detection.

Set the detection area. Click on the live video to specify the four vertexes of the

detection region, and right click to complete drawing.

Select the detection target. Human and vehicle are available. If the detection

target is not selected, all the detected targets will be reported, including the

human and vehicle.

Drag the slider to set the sensitivity value.

Sensitivity

: Range [1-100]. Sensitivity stands for the percentage of the body part

Summary of Contents for HiWatch HWI-B120H-U


































































































































































































Search results

Summary of Contents for HiWatch HWI-B120H-U

Reviews:

Related manuals for HiWatch HWI-B120H-U

Brands by name

Popular brands

HIKVISION HiWatch HWI-B120H-U, User Manual

Search results

Summary of Contents for HiWatch HWI-B120H-U

Reviews:

Related manuals for HiWatch HWI-B120H-U

Brands by name

Popular brands