HIKVISION HiWatch HWI-B120H-U User Manual Download

Page: 157 / 193

Network Camera User Manual

156

Counting

Counting function helps to calculate the number of people entered or exited a certain

configured area and is widely applied to the entrances or exits.

Compared with the people counting function supported by iDS camera, counting

function needs no camera calibration.

Notes:

It is recommended to install the camera as right above the entrance/exit as possible,

and make sure it is horizontal to improve the counting accuracy.

Steps:

Enter the Counting Configuration interface:

Configuration >Counting

Counting Configuration

Check the

Enable Counting

checkbox to enable the function.

Check the

Enable OSD Overlay

checkbox, and the real-time number of

people entered and exited is displayed on the live video.

Summary of Contents for HiWatch HWI-B120H-U


































































































































































































Search results

Summary of Contents for HiWatch HWI-B120H-U

Reviews:

Related manuals for HiWatch HWI-B120H-U

Brands by name

Popular brands

HIKVISION HiWatch HWI-B120H-U, User Manual

Search results

Summary of Contents for HiWatch HWI-B120H-U

Reviews:

Related manuals for HiWatch HWI-B120H-U

Brands by name

Popular brands