HIKVISION HiWatch HWI-B120H-U User Manual Download

Page: 131 / 193

Network Camera User Manual

130

You can press the Emergency button on the remote control to trigger the Emergency

Alarm in case of an emergency.

Note:

The remote control is required for the Emergency Alarm. Go to

Configuration >

System> System Settings > Remote Control

to study the remote control first.

Steps:

Enter the Emergency Alarm Settings interface:

Configuration > Event > Basic Event> Emergency Alarm

Setting Emergency Alarm

Check the checkbox to select the linkage methods taken for the Emergency alarm.

Click

Save

to save the settings.

Smart Events

You can configure the smart events by following the instructions in this section,

including audio exception detection, defocus detection, scene change detection,

intrusion detection, and line crossing detection, etc. These events can trigger the

linkage methods, such as Notify Surveillance Center, Send Email, Trigger Alarm

Output, etc.

Configuring Audio Exception Detection

Purpose:

Summary of Contents for HiWatch HWI-B120H-U


































































































































































































Search results

Summary of Contents for HiWatch HWI-B120H-U

Reviews:

Related manuals for HiWatch HWI-B120H-U

Brands by name

Popular brands

HIKVISION HiWatch HWI-B120H-U, User Manual

Search results

Summary of Contents for HiWatch HWI-B120H-U

Reviews:

Related manuals for HiWatch HWI-B120H-U

Brands by name

Popular brands