HIKVISION HiWatch HWI-B120H-U User Manual Download

Page: 165 / 193

Network Camera User Manual

164

Storage Settings

Before you start:

To configure record settings, please make sure that you have the network storage

device or local storage device configured.

Configuring Record Schedule

Purpose:

There are two kinds of recording for the cameras: manual recording and scheduled

recording. In this section, you can follow the instructions to configure the scheduled

recording. By default, the record files of scheduled recording are stored in the local

storage or in the network disk.

Steps:

Enter the Record Schedule Settings interface:

Configuration

Storage

Schedule Settings > Record Schedule

Recording Schedule Interface

Check the checkbox of

Enable

to enable scheduled recording.

Click

Advanced

to set the camera record parameters.

Summary of Contents for HiWatch HWI-B120H-U


































































































































































































Search results

Summary of Contents for HiWatch HWI-B120H-U

Reviews:

Related manuals for HiWatch HWI-B120H-U

Brands by name

Popular brands

HIKVISION HiWatch HWI-B120H-U, User Manual

Search results

Summary of Contents for HiWatch HWI-B120H-U

Reviews:

Related manuals for HiWatch HWI-B120H-U

Brands by name

Popular brands