HIKVISION DS-7304HUI-K4 User Manual Download Page 74

Page: 74 / 220

DS-73xxHUI-K4, DS-73xxHQI-K4, DS-90xxHUI-K8 DVR User Manual

UM DS-73xxHUI-K4 DS-73xxHQI-K4 DS-90xxHUI-K8 092017NA

Figure 87,

Alarm Settings – Alarm Input

Select Alarm Input No.

Input Alarm Name.

Select

N.O.

(normally open) or

N.C.

(normally closed) for alarm type.

Check the

Enable

checkbox to enable alarm.

Click

Set

to set the triggered channels, arming schedule, linkage actions, and PTZ

linking.

Figure 88,

Alarm Handling

Click

Apply

to save the settings.

Repeat steps 1 to 8 to configure other alarm input parameters.

If the settings can also be applied to other alarm inputs, click

Copy

and choose the

alarm input number.

Summary of Contents for DS-7304HUI-K4





























































































































































































































Search results

Summary of Contents for DS-7304HUI-K4

Reviews:

Brands by name

Popular brands

HIKVISION DS-7304HUI-K4, User Manual

Search results

Summary of Contents for DS-7304HUI-K4

Reviews:

Brands by name

Popular brands