HIKVISION DS-7304HUI-K4 User Manual Download Page 187

Page: 187 / 220

DS-73xxHUI-K4, DS-73xxHQI-K4, DS-90xxHUI-K8 DVR User Manual

UM DS-73xxHUI-K4 DS-73xxHQI-K4 DS-90xxHUI-K8 092017NA

187

Figure 263,

Bad Sector Detecting

Click

Pause

to pause the detection and click

Resume

to resume the detection.

If there is error information about the HDD, Click

Error Info

to view the information.

14.11

Configuring HDD Error Alarms

Purpose

You can configure the HDD error alarms when the HDD status is

Uninitialized

Abnormal

Go to Menu > System Configuration > Exceptions.

Select the Exception Type to

HDD Error

from the drop-down list.

Check the checkbox(s) below to select the linkage action(s) for an HDD error, as shown
in Figure 12-26.

The linkage actions can be selected to: Audible Warning, Notify Surveillance Center,
Send Email, and Trigger Alarm Output.

Summary of Contents for DS-7304HUI-K4





























































































































































































































Search results

Summary of Contents for DS-7304HUI-K4

Reviews:

Brands by name

Popular brands

HIKVISION DS-7304HUI-K4, User Manual

Search results

Summary of Contents for DS-7304HUI-K4

Reviews:

Brands by name

Popular brands