HIKVISION DS-7304HUI-K4 User Manual Download Page 45

Page: 45 / 220

DS-73xxHUI-K4, DS-73xxHQI-K4, DS-90xxHUI-K8 DVR User Manual

UM DS-73xxHUI-K4 DS-73xxHQI-K4 DS-90xxHUI-K8 092017NA

Figure 47,

Digital Zoom

Image Settings icon enters the Image Settings menu. Drag the mouse or click

to adjust the

image parameters, including brightness, contrast, and saturation.

Figure 48,

Image Settings

Enable Face Detection by clicking the icon. The dialog pops up as shown in Figure 3-6. Click

Yes

and the full-screen live view of the channel is enabled. Click

to exit from full-screen mode. You can

configure face detection only when it is supported by the connected camera.

Figure 49,

Enable Face Detection

Move the mouse onto the Information icon to show the real-time stream information, including

the frame rate, bit rate, resolution, and stream type.

Summary of Contents for DS-7304HUI-K4





























































































































































































































Search results

Summary of Contents for DS-7304HUI-K4

Reviews:

Brands by name

Popular brands

HIKVISION DS-7304HUI-K4, User Manual

Search results

Summary of Contents for DS-7304HUI-K4

Reviews:

Brands by name

Popular brands