HIKVISION DS-7304HUI-K4 User Manual Download Page 44

Page: 44 / 220

DS-73xxHUI-K4, DS-73xxHQI-K4, DS-90xxHUI-K8 DVR User Manual

UM DS-73xxHUI-K4 DS-73xxHQI-K4 DS-90xxHUI-K8 092017NA

Figure 45,

Switch Main and Aux Output

Use the mouse wheel to double-click on the screen again to switch to the
aux output, or click

Cancel

to cancel the operation.

Select the

Menu Output Mode

to others

from the right-click menu on the

monitor.

On the pop-up message box, click

Yes

to reboot the device to enable the

selected menu output as the main output.

You can select the

Menu Output Mode

under Menu > Configuration >

General > More Settings to

Auto

HDMI1/VGA

and

HDMI2

and then

reboot the device to switch the main output.

3.3.3

Quick Setting Toolbar in Live View Mode

On the screen of each channel, there is a quick setting toolbar that appears
when you click the screen.

Figure 46,

Quick Setting Toolbar

Refer to Table below for description of the Quick Setting Toolbar icons.

Table 1-12

Description of Quick Setting Toolbar Icons

Icons

Description

Icons

Description

Icons

Description

Start/Stop Manual
Recording

Instant Playback

Audio On/Mute

PTZ Control

Digital Zoom

Image Settings

Close Live View

Face Detection

Information

Capture

Live View
Strategy

Fisheye

Instant Playback shows only the record in the last five minutes. If no record is found, it means

there is no record during the last five minutes.

Digital Zoom zooms in the live image. You can zoom in the image to different proportions (1 to

16x) by moving the sliding bar. You can also scroll the mouse wheel to control the zoom in/out.

Summary of Contents for DS-7304HUI-K4





























































































































































































































Search results

Summary of Contents for DS-7304HUI-K4

Reviews:

Brands by name

Popular brands

HIKVISION DS-7304HUI-K4, User Manual

Search results

Summary of Contents for DS-7304HUI-K4

Reviews:

Brands by name

Popular brands