HIKVISION DS-7304HUI-K4 User Manual Download Page 209

Page: 209 / 220

DS-73xxHUI-K4, DS-73xxHQI-K4, DS-90xxHUI-K8 DVR User Manual

UM DS-73xxHUI-K4 DS-73xxHQI-K4 DS-90xxHUI-K8 092017NA

209

Figure 293,

User List

Click

to delete the selected user account.

17.5.3

Editing a User

Purpose

For the added user accounts, you can edit the parameters.

Go to Menu > System Configuration > User.

Select the user to be edited from the list.

Click

to enter the

Edit User

interface, as shown below.

Figure 294,

Edit User Interface

Edit the corresponding parameters.

•

Operator and Guest

You can edit user information, including user name, password,
permission level, and MAC address. Check

Change Password

checkbox to change the password; input new password in

Password

and

Confirm

text fields. A strong password is recommended.

Summary of Contents for DS-7304HUI-K4





























































































































































































































Search results

Summary of Contents for DS-7304HUI-K4

Reviews:

Brands by name

Popular brands

HIKVISION DS-7304HUI-K4, User Manual

Search results

Summary of Contents for DS-7304HUI-K4

Reviews:

Brands by name

Popular brands