manualshive.com logo in svg

HIKVISION DS-7304HUI-K4, User Manual

Share
Download
HIKVISION DS-7304HUI-K4 User Manual Download Page 214

DS-73xxHUI-K4, DS-73xxHQI-K4, DS-90xxHUI-K8 DVR User Manual 

UM DS-73xxHUI-K4 DS-73xxHQI-K4 DS-90xxHUI-K8 092017NA 

214 

18.1.3

 

DS-73xxHQI-K4 

Model 

 

DS-7304HQI-K4 

DS-7308HQI-K4 

DS-7316HQI-K4 

Video/Audio 
Input 

Video Compression 

H.265+/H.265/H.264+/H.264 

Analog Video Input 

4-ch 

8-ch 

16-ch 

BNC interface (1.0 Vp-p, 75 Ω), supporting Hikvision-C connection 

HDTVI Input 

3 MP, 1080p25, 1080p30, 720p25, 720p30, 720p50, 720p60 
Note: The 3 MP signal input is available only for channel 1 of DS-7304HQI-K4, channel 1/2 of 
DS-7308HQI-K4, and channel 1/2/3/4 of DS-7316HQI-K4. 

CVBS Input 

PAL/NTSC 

IP Video Input 

2-ch (up to 6-ch)   

2-ch (up to 10-ch) 

2-ch (up to 18-ch) 

Up to 4 MP resolution 
Supports H.265+/H.265/H.264+/H.264 IP cameras 

Audio Compression 

G.711u 

Audio Input 

4-ch, RCA (2.0 Vp-p, 1 KΩ) 

Video/Audio 
Output 

CVBS Output 

1-ch, BNC (1.0 Vp-p, 75 Ω), resolution: PAL: 704 × 576, NTSC: 704 × 480 

HDMI/VGA Output 

HDMI: 1-ch, 4K (3840 × 2160)/30 Hz, 2K (2560 × 1440)/60 Hz, 1920 × 1080/60 Hz, 1280 × 
1024/60 Hz, 1280 × 720/60 Hz, 1024 × 768/60 Hz 
VGA: 1-ch, 1920 × 1080/60 Hz, 1280 × 1024/60 Hz, 1280 × 720/60 Hz, 1024 × 768/60 Hz 

Encoding Resolution 

When 1080p Lite mode not enabled: 3 MP/1080p/720p/VGA/WD1/4CIF/CIF 
When 1080p Lite mode enabled: 3 MP/1080p lite/720p lite/VGA/WD1/4CIF/CIF 

Frame Rate 

Main stream: When 1080p Lite mode not enabled:   
For 3 MP stream access: 3 MP/1080p/720p/VGA/WD1/4CIF/CIF @ 15 fps 
For 1080p stream access: 1080p/720p @ 15 fps; VGA/WD1/4CIF/CIF @ 25 fps (P)/30 fps (N) 
For 720p stream access: 720p/VGA/WD1/4CIF/CIF @ 25 fps (P)/30 fps (N) 
When 1080p Lite mode enabled:   
3 MP @ 15 fps 
1080p lite/720p lite/VGA/WD1/4CIF/CIF @ 25fps (P)/30 fps (N) 
Sub-stream: WD1/4CIF @ 12 fps; CIF @ 25 fps (P)/30 fps (N) 

Video Bit Rate 

32 Kbps to 6 Mbps 

Audio Output 

2-ch, RCA (linear, 1 KΩ)   

Audio Bit Rate 

64 Kbps     

Dual Stream 

Supported 

Stream Type 

Video, Video & Audio 

Synchronous Playback 

4-ch 

8-ch 

16-ch 

Network 
Management 

Remote Connections 

128 

Network Protocols 

TCP/IP, PPPoE, DHCP, Hik-Connect, DNS, DDNS, NTP, SADP, NFS, iSCSI, UPnP™, HTTPS, ONVIF 

Hard Disk 

SATA 

4 SATA interfaces   

eSATA 

Supported 

Capacity 

Up to 8 TB capacity for each disk 

External 
Interface 

Two-Way Audio Input 

1-ch, RCA (2.0 Vp-p, 1 KΩ) (independent) 

Network Interface 

1, RJ-45 10M/100M/1000M self-adaptive Ethernet interface 

USB Interface 

Front panel: 2 × USB 2.0   
Rear panel: 1 × USB 3.0   

Serial Interface 

RS-232, RS-485 (full-duplex), keyboard 

Alarm In/Out 

16/4 

General 

Power Supply 

100 to 240 VAC 

Consumption (w/o HDD) 

≤30 W 

≤40 W 

≤55 W 

Working Temperature 

-10 to +55° C (+14 to +131° F) 

Working Humidity 

10% to 90% 

Dimensions (W × D × H) 

445 mm × 390 mm × 70 mm (17.5" × 15.4" × 2.8") 

Weight (w/o HDD) 

≤5 kg (11.0 lb) 

Summary of Contents for DS-7304HUI-K4





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands