HIKVISION DS-7304HUI-K4 User Manual Download Page 200

Page: 200 / 220

DS-73xxHUI-K4, DS-73xxHQI-K4, DS-90xxHUI-K8 DVR User Manual

UM DS-73xxHUI-K4 DS-73xxHQI-K4 DS-90xxHUI-K8 092017NA

200

Other

17.1

Configuring General Settings

Purpose

You can configure the output resolution, system time, mouse pointer speed, etc.

Go to Menu > System Configuration > General > General.

Figure 280,

General Settings Interface

Configure the following settings:

•

Language:

The default language used is

English

•

Output Standard:

Select the output standard to be PAL or NTSC.

•

VGA/HDMI Resolution:

Select the output resolution, which must be the same as

the resolution of the VGA/HDMI display.

VGA/HDMI1 Resolution

and

HDMI2 Resolution

can be configured separately. Up to

1920 × 1080/60 Hz resolution is supported for VGA/HDMI1 output and up to 4K (3840
× 2160)/30 Hz resolution is supported for HDMI2 output.

•

Time Zone:

Select the time zone.

•

Date Format:

Select the date format.

•

System Date:

Select the system date.

•

System Time:

Select the system time.

•

Mouse Pointer Speed:

Set the speed of mouse pointer; four levels are configurable.

•

Enable Password:

Enable/disable the use of the login password.

Summary of Contents for DS-7304HUI-K4





























































































































































































































Search results

Summary of Contents for DS-7304HUI-K4

Reviews:

Brands by name

Popular brands

HIKVISION DS-7304HUI-K4, User Manual

Search results

Summary of Contents for DS-7304HUI-K4

Reviews:

Brands by name

Popular brands