manualshive.com logo in svg

HIKVISION DS-7304HUI-K4, User Manual

Share
Download
HIKVISION DS-7304HUI-K4 User Manual Download Page 146

DS-73xxHUI-K4, DS-73xxHQI-K4, DS-90xxHUI-K8 DVR User Manual 

UM DS-73xxHUI-K4 DS-73xxHQI-K4 DS-90xxHUI-K8 092017NA 

146 

•

 

Multi-address Mode: 

The parameters of the two NIC cards can be configured 

independently. You can select LAN1 or LAN2 in the NIC type field for parameter 
settings.   

•

 

Net-fault Tolerance Mode: 

The two NIC cards use the same IP address, and you can 

select the Main NIC to LAN1 or LAN2. By this way, in case of one NIC card failure, 
the device will automatically enable the other standby NIC card so as to ensure the 
normal running of the whole system. 

 

 

The valid value of MTU is from 500 to 1500. 

If the DHCP server is available, you can check the checkbox of 

Enable

 

DHCP

 to 

automatically obtain an IP address and other network settings from that server. 

If DHCP is enabled, you can check the checkbox of 

Enable DNS DHCP 

or uncheck it 

and edit the 

Preferred DNS Server

 and 

Alternate DNS Server

. 

3.

 

After having configured the general settings, click 

Apply 

to save the settings.   

11.2

 

Configuring Advanced Settings 

11.2.1

 

Configuring PPPoE Settings 

Purpose 

The DVR allows access by Point-to-Point Protocol over Ethernet (PPPoE). 

1.

 

Go to Menu > System Configuration > Network > PPPoE. 

 

Figure 194,

 

PPPoE Settings Interface 

2.

 

Check the 

Enable

 

PPPoE

 checkbox to enable this feature. 

3.

 

Enter 

User Name

 and 

Password

 for PPPoE access. 

 

 

The User Name and Password should be assigned by your ISP. 

4.

 

Click 

Apply

 to save the settings. 

5.

 

After successful settings, the system asks you to reboot the device to 
enable the new settings, and the PPPoE dial-up is automatically 
connected after reboot. 

6.

 

You can go to Menu > Maintenance > System Info > Network interface to 
view the status of PPPoE connection.   

Summary of Contents for DS-7304HUI-K4





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands