HIKVISION DS-7304HUI-K4 User Manual Download Page 160

Page: 160 / 220

DS-73xxHUI-K4, DS-73xxHQI-K4, DS-90xxHUI-K8 DVR User Manual

UM DS-73xxHUI-K4 DS-73xxHQI-K4 DS-90xxHUI-K8 092017NA

160

Select the backup device from the

Device Name

drop-down list.

Click

Refresh

if the connected local backup device cannot be displayed. If

it fails to detect the backup device, check whether it is compatible with
the DVR. You can format the backup device if the format is incorrect.

Figure 212,

Export Network Packet

Click

Export

to start exporting.

After exporting is complete, click

to finish the packet export.

Figure 213,

Packet Export Attention

Up to 1 MB of data can be exported each time.

11.3.3

Checking Network Status

Purpose

You can also check the network status and quick set the network parameters
in this interface.

Go to Menu > Maintenance > Net Detect > Network Detection.

Click

Status

on the right bottom of the interface.

Summary of Contents for DS-7304HUI-K4





























































































































































































































Search results

Summary of Contents for DS-7304HUI-K4

Reviews:

Brands by name

Popular brands

HIKVISION DS-7304HUI-K4, User Manual

Search results

Summary of Contents for DS-7304HUI-K4

Reviews:

Brands by name

Popular brands