HIKVISION DS-7304HUI-K4 User Manual Download Page 49

Page: 49 / 220

DS-73xxHUI-K4, DS-73xxHQI-K4, DS-90xxHUI-K8 DVR User Manual

UM DS-73xxHUI-K4 DS-73xxHQI-K4 DS-90xxHUI-K8 092017NA

•

Full Screen Monitoring Dwell Time:

Sets

the time in seconds to show the alarm

event screen.

Set the camera order.

Click the

View

tab and select

Video Output Interface

from the drop-down list.

Figure 54,

Live View Camera Order

Click a window to select

, then double-click a camera to display in the camera list.

Setting an ‘X’ means the window will not display any camera.

You can also click

to start live view of all channels in order and click

to stop

live view of all channels. Click

to go to the previous or next page.

Click

Apply

If the sum of the analog and IP channels exceeds 25, up to 32-window division mode
is supported for the VGA/HDMI1 output.

3.6

Manual Video Quality Diagnostics

Purpose

The video quality of the analog channels can be diagnosed manually and you can view the
diagnostic results from a list.

Go to Menu > Manual > Manual Video Quality Diagnostics.

Figure 55,

Video Quality Diagnostics

Summary of Contents for DS-7304HUI-K4





























































































































































































































Search results

Summary of Contents for DS-7304HUI-K4

Reviews:

Brands by name

Popular brands

HIKVISION DS-7304HUI-K4, User Manual

Search results

Summary of Contents for DS-7304HUI-K4

Reviews:

Brands by name

Popular brands